How To String A Dewalt Weed Eater?

How To String A Dewalt Weed Eater?

| Step | Description | Image |
|—|—|—|
| 1. Remove the spool cover. | Use a flathead screwdriver to pry up the tabs on the side of the spool cover and remove it. |  |
| 2. Remove the old string. | Use a pair of pliers to pull out the old string. |  |
| 3. Thread the new string. | Thread the new string through the eyelets on the spool, following the manufacturer’s instructions. |  |
| 4. Reattach the spool cover. | Align the tabs on the spool cover with the slots on the weed eater and snap it back into place. |  |
| 5. Test the weed eater. | Turn on the weed eater and let it run for a few seconds to make sure the string is properly tensioned. |  |

A Dewalt weed eater is a powerful tool that can be used to quickly and easily remove weeds from your yard. However, in order to get the best results, it is important to make sure that the weed eater is properly strung. This guide will show you how to string a Dewalt weed eater in just a few simple steps.

Tools and Materials

• Dewalt weed eater
• String trimmer line
• Pliers
• Phillips head screwdriver
• Tape measure

Steps

1. Turn off the weed eater and disconnect the spark plug wire. This will prevent the weed eater from starting accidentally while you are working on it.
2. Remove the old string. To do this, you will need to unscrew the two screws that hold the string head in place. Once the screws are removed, you can carefully lift the string head off of the weed eater. The old string will be attached to the string head, so you can simply pull it off.
3. Measure the new string. The new string should be the same length as the old string. You can measure the old string to get the exact length, or you can simply use a tape measure to measure the distance from the center of the string head to the tip of the weed eater.
4. Thread the new string through the string head. To do this, you will need to start by threading the string through the hole in the center of the string head. Once the string is through the hole, you can continue to thread it through the slots in the string head. Make sure that the string is threaded through the slots in the same direction that it was on the old string.
5. Tighten the string. Once the string is threaded through the string head, you can tighten it by screwing the two screws that hold the string head in place. Be careful not to tighten the screws too much, as this could damage the string head.
6. Reattach the spark plug wire. Once the string is tightened, you can reattach the spark plug wire to the weed eater.

Now that you know how to string a Dewalt weed eater, you can keep your yard looking its best. By following these simple steps, you can easily and safely string your weed eater and get back to enjoying your outdoor space.

Here are some additional tips for stringing a Dewalt weed eater:

• Use a high-quality string trimmer line. A good-quality string will last longer and will cut through weeds more effectively.
• Be careful not to overtighten the string. Overtightening the string can damage the string head and make it difficult to start the weed eater.
• If the string breaks while you are using the weed eater, you can simply restring it by following the steps above.

3. Remove the spool cover.

To remove the spool cover on your Dewalt weed eater, follow these steps:

1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the spool cover release button. It is typically located on the side of the weed eater, near the top.
3. Press the release button and slide the spool cover off of the weed eater.

4. Remove the old string.

To remove the old string from your Dewalt weed eater, follow these steps:

1. Hold the weed eater upside down.
2. Use a pair of pliers to grip the end of the old string and pull it out of the spool.
3. Repeat this step until all of the old string has been removed.

.

Once you have removed the old string, you can replace it with a new string. To do this, follow these steps:

1. Thread the new string through the hole in the center of the spool.
2. Wrap the string around the spool, making sure that it is evenly spaced.
3. Trim the excess string so that it is about 1 inch longer than the cutting head.
4. Replace the spool cover and tighten the screws.

Now that you have replaced the string on your Dewalt weed eater, you can start using it again. Be sure to follow the manufacturer’s instructions for safe operation.

How To String A Dewalt Weed Eater?

Q: What tools do I need to string a Dewalt weed eater?

A: You will need the following tools:

• A Phillips head screwdriver
• A wire cutter
• A string trimmer line

Q: How do I remove the old string from my Dewalt weed eater?

A: 1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the string head on the weed eater. It is usually located near the bottom of the trimmer.
3. Use the Phillips head screwdriver to remove the screws that hold the string head in place.
4. Carefully remove the old string from the string head.

Q: How do I install the new string on my Dewalt weed eater?

A: 1. Cut two pieces of string trimmer line that are each 12 inches long.
2. Thread one end of each piece of string through the holes in the string head.
3. Make sure that the strings are parallel to each other and that they are the same length.
4. Use the wire cutter to trim the excess string.
5. Reattach the string head to the weed eater.

Q: How do I adjust the string tension on my Dewalt weed eater?

A: 1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the string tension adjustment screw on the weed eater. It is usually located near the string head.
3. Use the Phillips head screwdriver to turn the adjustment screw clockwise to increase the string tension or counterclockwise to decrease the string tension.
4. Reattach the spark plug wire and test the weed eater.

Q: What should I do if my Dewalt weed eater is not stringing properly?

A: There are a few things that you can check if your Dewalt weed eater is not stringing properly:

• Make sure that the string is installed correctly.
• Make sure that the string tension is correct.
• Check the condition of the string. If the string is frayed or damaged, it will need to be replaced.
• Clean the string head to remove any debris that may be preventing the string from feeding properly.

If you have checked all of these things and your Dewalt weed eater is still not stringing properly, you may need to take it to a service center for repairs.