How to String a Hart 20V Weed Eater in 5 Easy Steps

How to String a Hart 20V Weed Eater

Your Hart 20V weed eater is a powerful tool for keeping your yard free of weeds. But when the string breaks, it can be a pain to get it back in. Don’t worry, we’re here to help. In this article, we’ll show you how to string a Hart 20V weed eater in just a few simple steps.

We’ll also provide some tips on how to keep your weed eater running smoothly and avoid future string problems. So if you’re ready to get your weed eater back in action, read on!

Step	Instructions	Image
1	Remove the spool cover from the weed eater.
2	Unwind the old string from the spool.
3	Thread the new string through the eyelets on the spool.
4	Wind the new string onto the spool until it is tight.
5	Replace the spool cover.

How to String a Hart 20V Weed Eater?

A Hart 20V weed eater is a powerful tool that can help you quickly and easily remove weeds from your yard. However, if the string on your weed eater breaks, it can be difficult to know how to replace it. This guide will walk you through the process of stringing a Hart 20V weed eater, step-by-step.

Gather the necessary tools and materials

Before you begin, you will need to gather the following tools and materials:

• Hart 20V Weed Eater
• Replacement string
• Pliers
• Tape measure
• Flathead screwdriver

Remove the old string

To remove the old string, follow these steps:

1. Turn off the weed eater and disconnect the spark plug wire.
2. Use the pliers to loosen the string retainer.
3. Pull the old string out of the weed eater.

Install the new string

To install the new string, follow these steps:

1. Cut a piece of string that is 12 inches long.
2. Thread the string through the eyelets on the weed eater.
3. Pull the string taut and tighten the string retainer.

Test the weed eater

Once you have installed the new string, test the weed eater by turning it on and running it for a few seconds. The string should spin freely and should not come off of the weed eater.

Stringing a Hart 20V weed eater is a relatively simple task that can be completed in a few minutes. By following the steps in this guide, you can keep your weed eater running smoothly and efficiently.

Here are some additional tips for stringing a Hart 20V weed eater:

• Use a sharp pair of scissors to cut the string. A dull pair of scissors can damage the string and make it more difficult to thread through the eyelets.
• Be careful not to overtighten the string retainer. Overtightening the string can damage the weed eater.
• If the string breaks while you are using the weed eater, stop using the weed eater immediately and replace the string. Using a weed eater with a broken string can be dangerous.

By following these tips, you can safely and effectively string your Hart 20V weed eater.

How to String a Hart 20V Weed Eater?

Stringing a Hart 20V weed eater is a relatively simple task that can be completed in a few minutes. Here are the steps involved:

1. Turn off the weed eater and disconnect the battery. This will prevent you from accidentally starting the weed eater while you are working on it.
2. Remove the string retainer. The string retainer is a small plastic piece that holds the strings in place. It is located on the side of the weed eater. To remove it, simply pry it up with a screwdriver.
3. Cut two pieces of string to the same length. The length of the string will depend on the model of your weed eater. For most models, the string should be about 18 inches long.
4. Thread the strings through the holes in the weed eater. The holes are located on the front of the weed eater. The strings should be threaded through the holes in a criss-cross pattern.
5. Pull the strings taut and secure them with the string retainer. Once the strings are threaded through the holes, pull them taut and secure them with the string retainer.
6. Test the weed eater. Turn on the weed eater and let it run for a few seconds. Make sure that the strings are spinning evenly. If the strings are not spinning evenly, adjust them until they are.

Troubleshooting

If you are having trouble stringing your Hart 20V weed eater, here are a few troubleshooting tips:

• Make sure that the strings are the correct length. The strings should be about 18 inches long.
• Make sure that the strings are threaded through the holes in the correct order. The strings should be threaded through the holes in a criss-cross pattern.
• Make sure that the strings are pulled taut. If the strings are not pulled taut, they will not spin evenly.
• Make sure that the string retainer is secure. If the string retainer is not secure, the strings will come loose.

If you are still having trouble stringing your Hart 20V weed eater, you may need to contact the manufacturer for assistance.

Stringing a Hart 20V weed eater is a relatively simple task that can be completed in a few minutes. By following the steps in this guide, you can easily string your weed eater and get back to enjoying your yard.

How do I string a Hart 20V weed eater?

1. Turn off the weed eater and disconnect the battery.
2. Locate the string guide on the weed eater. It is a small metal or plastic piece that is located near the head of the weed eater.
3. Remove the string guide by unscrewing it or pressing down on the release tab and sliding it out.
4. Thread the new string through the eyelets on the weed eater head. The eyelets are small holes located on the inside of the weed eater head.
5. Pull the string through the string guide until it is taut.
6. Secure the string in place by tightening the string guide.
7. Reconnect the battery and turn on the weed eater.

What type of string do I need for my Hart 20V weed eater?

You will need to use .065-inch diameter nylon string for your Hart 20V weed eater.

How often do I need to string my Hart 20V weed eater?

You will need to string your Hart 20V weed eater whenever the string becomes frayed or damaged. This typically happens every 20-30 minutes of use.

What if I can’t string my Hart 20V weed eater?

If you are unable to string your Hart 20V weed eater, you can contact Hart customer service for assistance. You can also find helpful tips and videos on how to string a weed eater on the Hart website.

stringing a Hart 20V weed eater is a relatively simple task that can be completed in a few minutes. By following the steps outlined in this guide, you can ensure that your weed eater is properly strung and ready to use.

Here are the key takeaways from this guide:

• The correct string tension is essential for a weed eater to function properly.
• The string should be installed so that it is taut but not too tight.
• If the string breaks, it can be replaced easily by following the steps in this guide.

By following these tips, you can keep your Hart 20V weed eater in good working order and enjoy a weed-free yard all season long.