How To Replace String On Craftsman V20 Weed Eater?

How to Replace String on a Craftsman V20 Weed Eater

Your Craftsman V20 weed eater is a powerful tool that can help you keep your yard looking its best. But, like any tool, it needs to be maintained in order to work properly. One of the most important maintenance tasks is replacing the string when it becomes worn out.

Replacing the string on a Craftsman V20 weed eater is a simple task that can be completed in just a few minutes. In this article, we’ll walk you through the process step-by-step.

We’ll also provide some tips on how to choose the right replacement string and how to make your weed eater last longer. So, if your weed eater is starting to lose its edge, read on for all the information you need to know about replacing the string.

How To Replace String On Craftsman V20 Weed Eater?

| Step | Action | Tool |
|—|—|—|
| 1 | Remove the spool cover. | Flat-head screwdriver |
| 2 | Remove the old string. | Pliers |
| 3 | Thread the new string through the eyelets. | Needle-nose pliers |
| 4 | Wind the new string onto the spool. | |
| 5 | Replace the spool cover. | Flat-head screwdriver |

Image: [How to Replace String on a Craftsman V20 Weed Eater](https://www.homedepot.com/p/RYOBI-18-in-Corded-String-Trimmer-RY18LT25A/314362043)

This guide will show you how to replace the string on a Craftsman V20 weed eater. The Craftsman V20 weed eater is a popular model that is easy to use and maintain. Replacing the string is a simple task that can be completed in just a few minutes.

Gather Materials and Tools

To replace the string on your Craftsman V20 weed eater, you will need the following materials and tools:

• Craftsman V20 weed eater
• Replacement string
• Pliers
• Tape measure
• Safety glasses

Turn Off the Weed Eater and Disconnect the Spark Plug

Before you begin replacing the string on your weed eater, you must first turn it off and disconnect the spark plug. This will prevent the weed eater from starting accidentally and causing injury.

To turn off the weed eater, press the power button. To disconnect the spark plug, locate the spark plug wire and remove it from the spark plug.

Remove the Old String

The next step is to remove the old string from the weed eater. To do this, you will need to remove the spool cover.

The spool cover is located on the top of the weed eater. It is held in place by two screws. Use a Phillips head screwdriver to remove the screws.

Once the screws are removed, you can lift up the spool cover and remove the old string.

Install the New String

Now that you have removed the old string, you can install the new string. To do this, you will need to thread the new string through the spool and tensioner.

The spool is located on the bottom of the weed eater. The tensioner is located on the side of the weed eater.

To thread the string, start by feeding the end of the string through the hole in the spool. Then, thread the string through the tensioner.

Once the string is threaded, you can tighten the tensioner to secure the string in place.

Reattach the Spool Cover

Now that you have installed the new string, you can reattach the spool cover. To do this, simply replace the spool cover and tighten the screws.

Test the Weed Eater

Now that you have replaced the string on your weed eater, you can test it to make sure it is working properly. To do this, turn on the weed eater and let it run for a few seconds.

The weed eater should be able to cut through weeds and grass without any problems. If the weed eater is not working properly, you may need to adjust the tensioner or replace the string.

Replacing the string on a Craftsman V20 weed eater is a simple task that can be completed in just a few minutes. By following these steps, you can keep your weed eater in good working order and ensure that it is able to effectively cut through weeds and grass.

Here are some additional tips for maintaining your Craftsman V20 weed eater:

• Clean the weed eater after each use. This will help to prevent the build-up of dirt and debris, which can damage the engine.
• Oil the weed eater regularly. This will help to keep the engine running smoothly.
• Replace the spark plug every 100 hours of use. This will help to ensure that the weed eater is starting properly and running efficiently.

How To Replace String On Craftsman V20 Weed Eater?

This guide will show you how to replace the string on a Craftsman V20 weed eater. The Craftsman V20 weed eater is a popular model that is known for its power and durability. It is also relatively easy to maintain, making it a good choice for homeowners who need a weed eater that can handle tough jobs.

Replacing the string on the Craftsman V20 weed eater is a simple task that can be completed in just a few minutes. However, it is important to follow the steps carefully in order to avoid damaging the weed eater.

Tools and Materials

To replace the string on the Craftsman V20 weed eater, you will need the following tools and materials:

• Pliers
• New string for the weed eater
• Safety glasses

Step 1: Turn Off the Weed Eater

Before you begin, make sure that the weed eater is turned off and unplugged from the power outlet. This will prevent you from accidentally starting the weed eater while you are working on it.

Step 2: Remove the String Retainer Screws

The string retainer screws are located on the side of the weed eater. Use the pliers to loosen the screws and remove them.

Step 3: Carefully Remove the Old String

Once the string retainer screws are removed, you can carefully remove the old string from the weed eater. Be careful not to damage the weed eater’s spool.

Step 4: Thread the New String Through the Eyelets

The new string should be threaded through the eyelets on the weed eater’s spool. Make sure that the string is threaded through the eyelets in the correct order.

Step 5: Pull the String Taut and Tighten the String Retainer Screws

Once the new string is threaded through the eyelets, you can pull the string taut and tighten the string retainer screws. Make sure that the screws are tight enough to hold the string in place, but not so tight that you damage the weed eater.

Replacing the string on the Craftsman V20 weed eater is a simple task that can be completed in just a few minutes. By following these steps, you can keep your weed eater in good working order and ensure that it is ready to tackle any job.

How do I replace the string on my Craftsman V20 Weed Eater?

1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the string head. It is a small, plastic housing located on the underside of the weed eater.
3. Remove the string head cover. There will be a small screw or clip holding the cover in place.
4. Unwind the old string. There will be two pieces of string, one on each side of the head.
5. Thread the new string through the eyelets in the head. The eyelets are small holes located on the inside of the head.
6. Tighten the string head cover.
7. Reattach the spark plug wire.
8. Test the weed eater by running it on a low setting.

What type of string do I need for my Craftsman V20 Weed Eater?

You will need .095-inch diameter nylon string for your Craftsman V20 Weed Eater.

How long should the string be?

The string should be about 12 inches long.

How do I adjust the string tension?

The string tension can be adjusted by turning the screw on the side of the string head. Turn the screw clockwise to increase the tension and counterclockwise to decrease the tension.

My weed eater is not cutting grass, what could be wrong?

There are a few possible reasons why your weed eater is not cutting grass.

• The string is too short. Make sure the string is at least 12 inches long.
• The string is too tight. Loosen the string tension by turning the screw on the side of the string head counterclockwise.
• The string is tangled. Untangle the string and try again.
• The weed eater is not getting enough gas. Make sure the fuel tank is full and that the gas line is clear.
• The spark plug is fouled. Clean or replace the spark plug.

I am having trouble threading the new string through the eyelets, what can I do?

There are a few things you can do to make threading the new string through the eyelets easier.

• Use a thin piece of wire to guide the string through the eyelets.
• Soak the string in water for a few minutes to make it more pliable.
• Use a pair of needle-nose pliers to help thread the string through the eyelets.

I am still having trouble, can you help me?

If you are still having trouble threading the new string through the eyelets, you can contact Craftsman customer service for assistance.

In this tutorial, we have shown you how to replace the string on a Craftsman V20 weed eater. We hope that this information has been helpful and that you are now able to maintain your weed eater properly.

Here are the key takeaways from this tutorial:

• To replace the string on your Craftsman V20 weed eater, you will need to remove the old string, measure and cut new string, and then thread the new string through the weed eater.
• The old string can be removed by loosening the string lock knob and pulling the old string out of the weed eater.
• New string can be cut to the correct length by measuring the old string and adding 6 inches.
• The new string can be threaded through the weed eater by following the steps in the tutorial.

We hope that you have found this tutorial to be helpful. If you have any questions, please do not hesitate to contact us.