STIHL FS 40 C String Replacement: A Step-by-Step Guide
To replace the string, load new trimmer line into the fitted mowing head by winding its exposed spool or using its external-loading mechanism. A compatible prefilled spool is another option. The important first step is identifying the mowing head so you can use the appropriate loading procedure or replacement spool.
Identify the Mowing Head Before Buying Line
Match the replacement line, spool, and loading procedure to the fitted mowing head, not just the trimmer’s model name.
The mowing head is the assembly at the cutting end of the shaft. Its designation may be molded or printed on the housing. That designation matters especially on a used trimmer, where the original head may have been replaced.
There are two loading designs to distinguish:
- Standard spool heads: You open the head and wind replacement line directly onto the spool.
- Comfort-loading heads: You insert line from outside and turn the underside of the head to wind it without opening the housing.
Some heads also accept a compatible prefilled spool. Use a replacement spool listed as compatible with the fitted mowing head.
Do not choose a procedure solely because a head has a bump-feed button. Bump feeding describes how line advances during trimming, not necessarily how the spool is refilled.
How to Replace String on a STIHL FS 40 C
Replace the line by cleaning the trimmer, using the specified line, and reloading the fitted mowing head with its compatible method.
Step 1: Shut Down and Clean the Trimmer
- Turn the engine completely off and wait for the mowing head to stop.
- Let hot components cool, then disconnect the spark plug boot to prevent accidental starting while you work.
- Remove grass, dirt, and debris from around the head, its loading openings, and the housing seams.
Starting with the equipment completely powered off and thoroughly cleaned is part of replacement-line guidance. Cleaning also makes the head designation, winding arrows, and release points easier to find.
Gather the correct replacement line or prefilled spool, a suitable line-cutting tool, and any tool required by the head’s retaining mechanism. Avoid prying at the housing before you have identified how it opens.
Step 2: Select and Prepare the Replacement Line
Use the line diameter and refill length specified for the fitted mowing head. STIHL places those values on the head’s instruction card; they should not be guessed from the engine model or copied from instructions for a different head.
Color can help identify line diameter, but check the head’s instructions for the correct line. For example, red STIHL mowing line is roughly 0.11 inch (2.7 millimeters) in diameter.
For STIHL mowing line, soak it in water for 24 hours before winding, as recommended in STIHL’s line-preparation guidance. Nylon line loses moisture and elasticity over time; soaking helps restore flexibility and reduce premature wear.
Cut the refill length specified for your head. Do not add extra line simply because more appears to fit: a crowded spool can bind instead of feeding freely.
Step 3: Reload the Fitted Head
STIHL offers three common line-replacement methods. The fitted head’s design determines which options are available; use this table to choose the appropriate procedure.
| Fitted Head or Replacement Option | Reload Method | What Must Match |
|---|---|---|
| Standard winding spool | Remove and open the head, then wind the exposed spool | Line diameter, refill length, and winding direction |
| Comfort-loading head | Insert line externally and turn the underside to wind it | Loading arrangement, line diameter, and refill length |
| Compatible prefilled spool | Open the head and exchange the spool | The replacement spool’s listed head compatibility |
For the running check at the end of each procedure, work outdoors, wear eye protection and the trimmer’s required protective gear, and keep other people clear. The deflector and its line-limiting blade must be fitted and serviceable.
A standard spool head requires you to open the head and wind the replacement line directly onto the exposed spool.
- Remove the mowing head using its designated retaining mechanism, then open the housing. Do not assume that every head unscrews in the same direction.
- Lift out the spool, noting the position of any spring or other loose component. Remove the remaining old line and clear debris from the spool channels.
- Secure the new line in the spool’s starting points. Follow the arrows on the spool for winding direction rather than a generic clockwise or counterclockwise instruction.
- Wind the line evenly under light tension. If the spool has separate channels, keep each strand in its own channel. Use the retaining notches, if provided, to hold the ends while you reinstall the spool.
- Feed the cutting ends through the housing eyelets. Refit the spool and any spring, release the ends from their temporary retaining notches, and close the housing fully.
- Reinstall the head securely. Make sure neither line end is trapped under the cover, and trim excess line so it does not extend beyond the deflector’s line-limiting blade.
- Reconnect the spark plug boot and start the trimmer outdoors. Check for smooth operation and normal line feeding. Shut it off immediately if the head vibrates unusually, the cover loosens, or the line will not feed.
A comfort-loading head lets you reload from outside without opening the housing.
- Leave the head installed and closed for a normal external reload. Position any loading marks as indicated on the head.
- Insert the replacement line into the loading openings in the arrangement required by that head. Do not assume every comfort head uses the same threading path.
- Before winding, make sure equal lengths of line protrude from both sides.
- Turn the underside of the head in the marked winding direction. Keep both cutting ends outside the housing rather than winding them completely inside.
- Check that the head remains securely attached and fully closed. Trim excess line so it does not extend beyond the deflector’s line-limiting blade.
- Reconnect the spark plug boot and test outdoors. Confirm smooth running and normal line feeding; stop the engine before investigating any snag, vibration, or loose component.
If line will not enter the loading openings, do not force it. Old line may still be caught inside, or the loading passages may not be aligned.
A compatible prefilled spool lets you open the head and exchange the empty spool for one listed for that exact head.
- Open the head using its designated release mechanism, removing the head first if its design requires it.
- Remove the empty spool. Keep any spring or other reusable component in its correct position.
- Install the prefilled spool listed for that exact head. Route its line ends through the housing eyelets and release any temporary line retainers.
- Seat the spool properly, close the housing completely, and reinstall the head if it was removed.
- Check that the head is secure and that no line is pinched beneath the cover. Trim excess line so it does not extend beyond the deflector’s line-limiting blade.
- Confirm that the head runs smoothly and advances line normally. Shut down before making any adjustment.
Fix Line That Will Not Load or Feed
Diagnose the obstruction before adding more line or replacing the whole head. Many reload problems come from trapped remnants, crossed winding, or a spool that is not seated correctly.
Before making a correction, stop the engine, wait for the head to stop, and disconnect the spark plug boot.
| Symptom | Likely Cause | Correction |
|---|---|---|
| New line will not enter a comfort-loading head | Loading passages are misaligned, or old line remains inside | Align the loading marks; open and clear the head if it remains blocked |
| Winding becomes tight before the refill is loaded | Incorrect line diameter, excessive refill length, or an internal snag | Confirm the head’s line requirements and remove the obstruction |
| A freshly loaded spool will not feed | Crossed winding, wrong winding direction, or line left in retaining notches | Rewind in the arrow direction and release the retained ends |
| Only one cutting end appears | One end has retracted, broken, or become trapped | Open the head and recover or replace the trapped strand |
| The cover will not close fully | Spool or spring is misseated, line is pinched, or the spool is incompatible | Correct the seating and verify spool compatibility; do not force the cover |
After a correction, close the housing completely, secure the head, and trim excess line within the deflector’s cutting limit. If the housing will not latch, the head remains loose, or unusual vibration continues, stop using it and have the damaged or incompatible part addressed.
Check the Reload and Keep the Line Feeding
A successful reload leaves a closed, securely mounted head with both cutting ends exposed. During the running check, the head should turn smoothly and release line through its normal feed mechanism.
Before returning to regular trimming, confirm:
- The cover is fully seated, with all catches or retainers engaged.
- Neither cutting end is trapped under the cover.
- The head has no visible cracks or damaged retaining parts.
- The deflector and line-limiting blade are intact.
- The line advances without repeated sticking.
Keep the line package information for the next refill. Clear grass buildup from the head rather than packing fresh line around debris, and inspect the eyelets if the line repeatedly breaks at the housing.
Once the head runs smoothly and feeds correctly, resume trimming. If it still jams after a careful reload, address the head or spool problem instead of continuing to force the feed mechanism.
Frequently Asked Questions
What Does the C Mean on a STIHL FS 40 C?
The C identifies a comfort-feature version of a STIHL trimmer; it does not identify the mowing head installed on it. Some mowing heads have a comfort function that lets you insert line to load it. Read the designation on the head itself to determine its loading method.
Can I Use Thicker String for Heavy Weeds?
Use thicker line only if it is approved for both the fitted head and the trimmer. Longer, denser grass can call for thicker line, but thicker line also requires more power. A heavy-duty line available on the store shelf is not necessarily suitable for your trimmer head.
What If the Mowing Head Markings Are Unreadable?
Identify the head before buying a replacement spool or guessing its line size. The dealer can also help replace the line if the housing will not open normally or the loading mechanism is unclear. Bring the trimmer or the removed head so compatibility can be checked directly.
What gauge trimmer line does a STIHL FS 40 C use?
The correct line diameter depends on the fitted mowing head, not just the FS 40 C model name. STIHL notes that not all trimmer line is compatible with every trimmer head. Use the diameter listed on that head’s instruction card rather than selecting line by color alone.
