How To String Makita Weed Eater?

How to String a Makita Weed Eater

Your Makita weed eater is a powerful tool that can help you keep your yard looking its best. But if the string breaks, it can be a pain to replace. Luckily, stringing a Makita weed eater is a relatively simple task that can be completed in just a few minutes.

In this article, we’ll walk you through the process of stringing a Makita weed eater, step by step. We’ll also provide some tips and tricks to help you get the job done quickly and easily.

So whether you’re a new owner of a Makita weed eater or you’re just looking for a refresher, read on for all the information you need to know about stringing your weed eater.

Step	Instructions	Image
1	Remove the spool cover from the weed eater.
2	Unwind the old string from the spool.
3	Thread the new string through the eyelets on the spool.
4	Wind the new string onto the spool.
5	Replace the spool cover.

A Makita weed eater is a powerful tool that can be used to quickly and easily remove weeds from your yard. However, in order to get the best results, it is important to know how to string the weed eater properly. This guide will walk you through the process of stringing a Makita weed eater, step-by-step.

Tools and Materials

The following tools and materials are required to string a Makita weed eater:

• Makita weed eater
• String trimmer line
• Replacement spool (optional)
• Pliers
• Phillips head screwdriver
• Tape measure

Step-by-step Instructions

1. Remove the spool cover. The spool cover is located on the side of the weed eater. To remove it, simply unscrew the two screws that hold it in place.
2. Remove the old string. The old string is usually wound around the spool. To remove it, simply pull it off of the spool.
3. Install the new string. The new string is usually packaged in a spool. To install it, simply unwind the string from the spool and thread it through the eyelets on the weed eater.
4. Adjust the string tension. The string tension is important for ensuring that the weed eater cuts through weeds effectively. To adjust the string tension, simply turn the tension knob on the weed eater until the string is taut.
5. Reattach the spool cover. Once the string is installed and the tension is adjusted, simply reattach the spool cover.

Troubleshooting

If you are having trouble stringing your Makita weed eater, there are a few things you can check:

• Make sure that you are using the correct type of string. The string should be made of nylon or polyethylene and should be the correct diameter for your weed eater.
• Make sure that the string is long enough. The string should be long enough to reach from the spool to the tip of the weed eater.
• Make sure that the string is installed correctly. The string should be threaded through the eyelets on the weed eater and should be taut.

If you are still having trouble, you can contact Makita customer service for assistance.

Stringing a Makita weed eater is a simple process that can be completed in a few minutes. By following these step-by-step instructions, you can ensure that your weed eater is properly strung and ready to use.

How to String a Makita Weed Eater

Stringing a Makita weed eater is a simple task that can be completed in just a few minutes. By following these steps, you can ensure that your weed eater is properly strung and ready to use.

1. Gather your tools

Before you begin, you will need to gather the following tools:

• A Phillips head screwdriver
• A string trimmer line
• A pair of pliers

2. Turn off the weed eater and disconnect the spark plug wire

Before you can begin stringing your weed eater, you will need to turn it off and disconnect the spark plug wire. This will help to prevent any injuries from occurring.

To turn off the weed eater, locate the power switch and turn it to the off position. To disconnect the spark plug wire, locate the spark plug boot and pull it off of the spark plug.

3. Remove the trimmer head cover

The next step is to remove the trimmer head cover. This will expose the trimmer head and allow you to access the string.

To remove the trimmer head cover, locate the two screws that hold it in place. Use a Phillips head screwdriver to unscrew the screws and remove the cover.

4. Insert the string

Now that the trimmer head cover is removed, you can insert the string.

To insert the string, start by threading one end of the string through the hole in the center of the trimmer head. Then, thread the string through the eyelets on the inside of the trimmer head.

Once the string is threaded through the eyelets, pull it tight and trim off any excess string.

5. Replace the trimmer head cover

The final step is to replace the trimmer head cover.

To replace the trimmer head cover, simply line up the cover with the trimmer head and press down until it snaps into place.

By following these steps, you can easily string your Makita weed eater. With a properly strung weed eater, you can be sure that you will have the power and performance you need to get the job done.

How do I string a Makita weed eater?

1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the string spool. It is usually located on the top of the weed eater.
3. Remove the string spool cover. There will be a small release button or tab that you need to press to release the cover.
4. Unwind the old string from the spool. You can do this by hand or by using a pair of pliers.
5. Thread the new string through the eyelets on the weed eater. The eyelets are located on the top of the weed eater, near the string spool.
6. Wind the new string onto the spool. Start by winding the string around the spool in a clockwise direction. Once you have reached the end of the spool, continue winding the string in a counterclockwise direction.
7. Tighten the string spool. There will be a small screw or knob on the side of the weed eater. Turn the screw or knob clockwise to tighten the string spool.
8. Reattach the string spool cover.
9. Reconnect the spark plug wire.
10. Test the weed eater to make sure that it is working properly.

What type of string do I need for my Makita weed eater?

You will need to use a .095″ (2.4 mm) diameter nylon string for your Makita weed eater.

How long should the string be for my Makita weed eater?

The string should be about 18 inches (45 cm) long.

**How do I adjust the string tension on my Makita weed eater?

The string tension can be adjusted by turning the screw or knob on the side of the weed eater. Turn the screw or knob clockwise to increase the string tension and counterclockwise to decrease the string tension.

**What if the string breaks while I’m using my Makita weed eater?

If the string breaks while you’re using your Makita weed eater, you can simply restring it by following the steps above.

**How do I clean the string guide on my Makita weed eater?

To clean the string guide on your Makita weed eater, you will need to:

1. Turn off the weed eater and disconnect the spark plug wire.
2. Remove the string spool cover.
3. Use a small brush or a piece of cloth to clean the string guide.
4. Reattach the string spool cover.
5. Reconnect the spark plug wire.

In this blog post, we have discussed how to string a Makita weed eater. We have covered the steps in detail, with images to help you visualize the process. We hope that this information has been helpful, and that you are now able to string your Makita weed eater with ease.

Here are some key takeaways from this blog post:

• To string a Makita weed eater, you will need a Phillips head screwdriver, a string trimmer line, and a pair of pliers.
• The first step is to remove the trimmer head from the weed eater.
• Next, you will need to loosen the screws on the inside of the trimmer head.
• Once the screws are loose, you can remove the old string.
• To install the new string, you will need to thread it through the holes in the trimmer head.
• Once the string is threaded through the holes, you can tighten the screws on the inside of the trimmer head.
• Finally, you can reattach the trimmer head to the weed eater.

We hope that this blog post has been helpful. If you have any questions, please feel free to leave a comment below.