How To Add Line To Stihl Weed Eater?

How To Add Line To Stihl Weed Eater

Your Stihl weed eater is a powerful tool that can help you keep your yard looking its best. But if the line runs out, you’ll need to know how to add more. This is a simple process that only takes a few minutes.

In this article, we’ll show you how to add line to your Stihl weed eater. We’ll cover everything from finding the right line to threading it through the machine. So if you’re ready to get started, read on!

Steps to Add Line to Your Stihl Weed Eater

1. Turn off the weed eater and disconnect the spark plug wire. This will prevent the machine from starting accidentally while you’re working on it.
2. Locate the line spool. The line spool is usually located on the top of the weed eater. It’s a cylindrical container with a hole in the center.
3. Remove the line spool cover. The line spool cover is usually held in place by a screw or a clip. Remove the screw or clip to remove the cover.
4. Thread new line through the eyelet. The eyelet is a small hole in the center of the line spool. Thread the new line through the eyelet and pull it through until it comes out the other side.
5. Wind the line around the spool. Hold the end of the line in one hand and wind it around the spool in a clockwise direction. Continue winding the line until it’s about halfway full.
6. Trim the excess line. Use a pair of scissors to trim the excess line from the spool.
7. Replace the line spool cover. Replace the line spool cover and tighten the screw or clip to secure it in place.
8. Reconnect the spark plug wire. Reconnect the spark plug wire to the spark plug.
9. Turn on the weed eater and test it out. Make sure the weed eater is working properly by running it for a few seconds.

Step	Instructions	Image
1	Turn off the weed eater and disconnect the spark plug wire.
2	Remove the old line from the weed eater.
3	Measure the new line to the correct length.
4	Thread the new line through the eyelets on the weed eater.
5	Tighten the line guides to secure the line.
6	Test the weed eater to make sure the line is working properly.

How To Add Line To Stihl Weed Eater?

Tools and Materials Needed

To add line to your Stihl weed eater, you will need the following tools and materials:

• Stihl weed eater
• Replacement line
• Pliers
• Tape measure

Step-by-Step Instructions

1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the line spool on the weed eater. It is usually located on the side of the engine.
3. Remove the line spool cover.
4. Remove the old line from the spool.
5. Measure the length of line you need. The length of line you need will depend on the size of your weed eater.
6. Cut the new line to the desired length.
7. Thread the new line through the eyelet on the spool.
8. Wind the new line around the spool in a clockwise direction.
9. Make sure the line is evenly distributed around the spool.
10. Replace the line spool cover.
11. Reconnect the spark plug wire.
12. Turn on the weed eater and test the line.

Troubleshooting

If you are having trouble adding line to your Stihl weed eater, here are a few troubleshooting tips:

• Make sure you are using the correct type of line for your weed eater.
• Make sure the line is the correct length.
• Make sure the line is threaded through the eyelet on the spool correctly.
• Make sure the line is evenly distributed around the spool.
• If you are still having trouble, you may need to take your weed eater to a qualified service center.

Adding line to your Stihl weed eater is a simple task that can be completed in a few minutes. By following these steps, you can keep your weed eater running smoothly and efficiently.

How To Add Line To Stihl Weed Eater?

Stihl weed eaters are some of the most popular and powerful weed trimmers on the market. They’re also relatively easy to use and maintain. However, one thing that can be tricky is adding new line to the trimmer.

In this guide, we’ll show you how to add line to a Stihl weed eater in a few simple steps.

Step 1: Turn Off the Weed Eater

The first thing you need to do is turn off the weed eater. This will prevent you from accidentally starting the trimmer while you’re working on it.

Step 2: Remove the Old Line

Next, you need to remove the old line from the trimmer. To do this, locate the line spool on the trimmer. It’s usually located at the back of the trimmer, near the handle.

The line spool is held in place by a small screw. Use a Phillips head screwdriver to loosen the screw and remove the line spool.

Once the line spool is removed, you can remove the old line. Simply pull it out of the trimmer.

Step 3: Load the New Line

Now it’s time to load the new line onto the trimmer. To do this, you’ll need to thread the line through the eyelets on the line spool.

The eyelets are located on the inside of the line spool. They’re small holes that the line will pass through.

Start by threading the line through the first eyelet. Then, thread the line through the second eyelet.

Once the line is threaded through the eyelets, you can start wrapping it around the spool.

Start by wrapping the line around the spool in a clockwise direction. Wrap the line tightly, but don’t overtighten it.

Continue wrapping the line around the spool until it’s full.

Step 4: Secure the New Line

Once the line is full, you need to secure it in place. To do this, use a pair of pliers to bend the end of the line over the spool.

Bend the line over so that it’s flush with the edge of the spool.

This will help to keep the line from slipping off the spool.

Step 5: Replace the Line Spool

Now it’s time to replace the line spool. To do this, simply reverse the steps you took to remove it.

First, insert the line spool into the trimmer. Then, tighten the screw to secure the line spool in place.

Step 6: Turn On the Weed Eater

Now that you’ve added new line to the trimmer, you can turn it on and test it out.

Start by turning on the trimmer and letting it run for a few seconds. Then, hold the trimmer up to a piece of wood and start trimming.

The line should cut through the wood easily. If it doesn’t, you may need to adjust the line tension.

To adjust the line tension, locate the line tension knob on the trimmer. It’s usually located near the handle.

Turn the knob clockwise to tighten the line or counterclockwise to loosen it.

Once the line is properly tensioned, you can start trimming.

Troubleshooting

If you’re having trouble adding line to your Stihl weed eater, here are a few troubleshooting tips:

• Make sure that the line is the correct size for your trimmer.
• Make sure that the line is threaded through the eyelets on the line spool correctly.
• Make sure that the line is wrapped around the spool tightly.
• Make sure that the line is secured in place by the line spool screw.
• If you’re still having trouble, you can contact Stihl customer service for assistance.

Additional Tips

Here are a few additional tips for adding line to your Stihl weed eater:

• Use a sharp pair of pliers to bend the end of the line over the spool. This will help to keep the line from slipping off the spool.
• When trimming, hold the trimmer up to a piece of wood and start trimming. The line should cut through the wood easily. If it doesn’t, you may need to adjust the line tension.
• To adjust the line tension, locate the line tension knob on the trimmer. It’s usually located near the handle.
• Turn the knob clockwise to tighten the line or counterclockwise to loosen it.
• Once the line is properly tensioned, you can start trimming.

  How do I add line to my Stihl weed eater?

1. Turn off the weed eater and disconnect the spark plug wire. This will prevent the engine from starting accidentally while you are working on it.
2. Locate the line spool. The line spool is usually located on the top of the weed eater, near the handle.
3. Remove the line spool cover. The line spool cover is usually held in place by a Phillips head screw. Remove the screw and set the cover aside.
4. Thread new line through the eyelet on the line spool. The eyelet is a small hole in the center of the line spool.
5. Wind the new line onto the spool. Start by winding the line around the spool in a clockwise direction. Continue winding the line until the spool is full.
6. Replace the line spool cover. Secure the line spool cover with the Phillips head screw.
7. Reconnect the spark plug wire.
8. Test the weed eater to make sure that it is working properly.

What type of line should I use for my Stihl weed eater?

You should use a nylon monofilament line for your Stihl weed eater. Nylon monofilament line is lightweight and durable, and it will provide you with the best performance.

How long should the line be for my Stihl weed eater?

The length of the line for your Stihl weed eater will depend on the size of the weed eater. For a small weed eater, you will need a line that is about 15 feet long. For a larger weed eater, you will need a line that is about 20 feet long.

How do I adjust the line on my Stihl weed eater?

To adjust the line on your Stihl weed eater, follow these steps:

1. Turn off the weed eater and disconnect the spark plug wire.
2. Locate the line adjustment screw. The line adjustment screw is usually located on the side of the weed eater.
3. Turn the line adjustment screw clockwise to tighten the line or counterclockwise to loosen the line.
4. Reattach the spark plug wire.
5. Test the weed eater to make sure that the line is adjusted properly.

What do I do if the line breaks while I’m using my Stihl weed eater?

If the line breaks while you’re using your Stihl weed eater, follow these steps:

1. Turn off the weed eater and disconnect the spark plug wire.
2. Remove the line spool cover.
3. Thread the new line through the eyelet on the line spool.
4. Wind the new line onto the spool.
5. Replace the line spool cover.
6. Reconnect the spark plug wire.
7. Test the weed eater to make sure that it is working properly.

adding line to your Stihl weed eater is a simple task that can be completed in just a few minutes. By following the steps outlined in this guide, you can ensure that your weed eater is properly equipped to handle any yard-trimming job.

Here are the key takeaways:

• Use the correct type of line for your weed eater.
• Make sure the line is the correct length for your weed eater.
• Follow the manufacturer’s instructions for adding line to your weed eater.
• Inspect your weed eater regularly and replace the line as needed.

By following these tips, you can keep your Stihl weed eater in top condition and ensure that it is always ready to tackle any yard-trimming job.