How To Replace A Carburetor On A Husqvarna Weed Eater?

How to Replace a Carburetor on a Husqvarna Weed Eater

Your Husqvarna weed eater is a powerful tool that can make quick work of overgrown weeds and grass. But when the carburetor starts to give you trouble, it can be a major pain. A carburetor is responsible for mixing fuel and air in the correct proportions to create a combustible mixture that powers your engine. If the carburetor is not working properly, your weed eater will either not start or will run poorly.

Replacing a carburetor on a Husqvarna weed eater is a relatively simple task that can be completed in about an hour. However, it is important to follow the steps carefully to avoid damaging your engine. In this article, we will walk you through the process of replacing a carburetor on a Husqvarna weed eater.

We’ll start by discussing the tools and materials you’ll need, then we’ll take you through the steps of removing the old carburetor, installing the new carburetor, and testing your weed eater to make sure it’s running properly. By the end of this article, you’ll be able to replace a carburetor on your Husqvarna weed eater like a pro.

Step	Tools	Instructions
1	Phillips head screwdriver	Remove the air filter cover.
2	10mm wrench	Disconnect the fuel line from the carburetor.
3	13mm wrench	Remove the carburetor mounting bolts.
4	Needle nose pliers	Remove the choke cable from the carburetor.
5	Flathead screwdriver	Remove the throttle cable from the carburetor.
6	Carefully remove the carburetor from the engine.
7	Clean the carburetor with carburetor cleaner.
8	Inspect the carburetor for damage.
9	Replace the carburetor gasket.
10	Reinstall the carburetor on the engine.
11	Reconnect the fuel line, choke cable, and throttle cable.
12	Reinstall the air filter cover.

A carburetor is a device that mixes fuel and air in the correct proportions to allow an engine to run efficiently. If the carburetor on your Husqvarna weed eater becomes clogged or damaged, it can cause the engine to run poorly or not at all. Replacing the carburetor is a relatively simple task that can be completed in about an hour. In this guide, we will walk you through the steps of replacing the carburetor on a Husqvarna weed eater.

Tools and Materials Needed

• Replacement carburetor
• Wrench
• Screwdriver
• Pliers
• Penetrating oil
• Rags

Step-by-Step Instructions

1. Turn off the weed eater and disconnect the spark plug wire.
2. Remove the air filter cover.
3. Locate the carburetor and disconnect the fuel line.
4. Remove the carburetor mounting bolts.
5. Carefully remove the carburetor from the engine.
6. Clean the carburetor body with a rag and penetrating oil.
7. Inspect the carburetor for damage.
8. Install the new carburetor.
9. Reconnect the fuel line and air filter cover.
10. Reconnect the spark plug wire.
11. Start the weed eater and test it for proper operation.

Replacing the carburetor on a Husqvarna weed eater is a relatively simple task that can be completed in about an hour. By following the steps in this guide, you can have your weed eater back up and running in no time.

Here are some additional tips for replacing the carburetor on a Husqvarna weed eater:

• Make sure to use the correct replacement carburetor for your model of weed eater.
• Be careful not to damage the carburetor body when removing it from the engine.
• Inspect the carburetor for damage before installing the new one.
• Make sure to reconnect all of the fuel and air lines properly before starting the weed eater.

By following these tips, you can ensure that your Husqvarna weed eater is running properly and efficiently.

3. Remove the old carburetor

To remove the old carburetor, you will need to:

1. Remove the air filter cover.
2. Disconnect the fuel line from the carburetor.
3. Disconnect the choke cable from the carburetor.
4. Remove the carburetor mounting bolts.
5. Remove the carburetor from the engine.

1. Remove the air filter cover

The air filter cover is located on the top of the carburetor. To remove it, you will need to:

1. Locate the air filter cover.
2. Press down on the tabs on the sides of the air filter cover and pull it up.

2. Disconnect the fuel line from the carburetor

The fuel line is connected to the carburetor by a quick-connect fitting. To disconnect the fuel line, you will need to:

1. Locate the fuel line.
2. Press down on the release button on the quick-connect fitting and pull the fuel line off.

3. Disconnect the choke cable from the carburetor

The choke cable is connected to the carburetor by a screw. To disconnect the choke cable, you will need to:

1. Locate the choke cable.
2. Loosen the screw that secures the choke cable to the carburetor.
3. Pull the choke cable off of the carburetor.

4. Remove the carburetor mounting bolts

The carburetor is mounted to the engine by two bolts. To remove the carburetor mounting bolts, you will need to:

1. Locate the carburetor mounting bolts.
2. Use a wrench to loosen and remove the carburetor mounting bolts.

5. Remove the carburetor from the engine

Once the carburetor mounting bolts are removed, you can remove the carburetor from the engine. To do this, you will need to:

1. Grasp the carburetor and pull it up and away from the engine.
2. Be careful not to damage the gaskets.

4. Clean the carburetor housing

Before you can install the new carburetor, you will need to clean the carburetor housing. To do this, you will need to:

1. Remove the carburetor bowl.
2. Remove the float and needle valve.
3. Clean the carburetor body.
4. Inspect the carburetor jets.
5. Replace the carburetor gaskets.

1. Remove the carburetor bowl

The carburetor bowl is located at the bottom of the carburetor. To remove the carburetor bowl, you will need to:

1. Locate the carburetor bowl.
2. Use a screwdriver to pry up on the lock tab and remove the carburetor bowl.

2. Remove the float and needle valve

The float and needle valve are located inside the carburetor bowl. To remove them, you will need to:

1. Locate the float and needle valve.
2. Use a pair of needle-nose pliers to grasp the float and pull it up.
3. Use a small screwdriver to pry up on the needle valve and remove it.

3. Clean the carburetor body

The carburetor body is the main part of the carburetor. To clean it, you will need to:

1. Remove all of the old gaskets from the carburetor body.
2. Use a carburetor cleaner to clean the inside of the carburetor body.
3. Be careful not to damage the small parts inside the carburetor body.

4. Inspect the carburetor jets

The carburetor jets are small passages that control the flow of fuel and air into the carburetor. To inspect them, you will need to:

1. Remove the carburetor jets.
2. Use a small screwdriver to clean the jets.
3. Be careful not to damage the jets.

5. Replace the carburetor gaskets

The carburetor gaskets seal the carburetor to the engine and the carburetor bowl to the carburetor body. To replace them, you will need to:

1. Remove the old gaskets.
2. Apply a thin coat of gasket sealant to the new gaskets.
3. Install the new gaskets.

Once you have cleaned the carburetor housing and replaced the carburetor gaskets, you can install the new carburetor. To do this, you will need to:

1. Align the carburetor with the engine.
2. Install the carburetor mounting bolts.
3. Connect the fuel line to the carburetor.
4. Connect the choke cable to the carburetor.
5. Install the air filter cover.

Once the new carburetor is installed, you can start the engine and test it. If the engine does not start, or if it runs poorly, you may need to adjust the

How do I remove the old carburetor?

1. Turn off the weed eater and disconnect the spark plug wire.
2. Remove the air filter cover.
3. Locate the carburetor and identify the two bolts that hold it in place.
4. Use a wrench to loosen the bolts and remove the carburetor.
5. Be careful not to spill any gasoline.

How do I install the new carburetor?

1. Place the new carburetor on the engine.
2. Align the two bolts with the holes in the carburetor and tighten them with a wrench.
3. Reattach the air filter cover.
4. Reconnect the spark plug wire.

What is the difference between a carburetor and a fuel injection system?

A carburetor is a mechanical device that mixes air and fuel in the correct proportions to create a combustible mixture. A fuel injection system uses electronic sensors to measure the amount of air and fuel needed, and then injects the fuel directly into the engine.

Why do I need to replace my carburetor?

There are a few reasons why you might need to replace your carburetor. The most common reason is that the carburetor is dirty or clogged. This can cause the engine to run poorly or not at all. Another reason to replace the carburetor is if it is damaged. A damaged carburetor can cause the engine to run erratically or make strange noises.

How can I prevent my carburetor from becoming dirty or clogged?

There are a few things you can do to prevent your carburetor from becoming dirty or clogged. First, make sure to use clean fuel. Second, keep the air filter clean. Third, avoid running the engine at high speeds for extended periods of time.

What are the symptoms of a bad carburetor?

There are a few symptoms that can indicate a bad carburetor. These include:

• The engine starts hard or runs rough.
• The engine stalls or hesitates when accelerating.
• The engine smokes excessively.
• The engine uses more fuel than usual.

If you experience any of these symptoms, it is possible that your carburetor needs to be replaced.

How much does it cost to replace a carburetor?

The cost of replacing a carburetor can vary depending on the make and model of your weed eater. The average cost is between $50 and $100. However, it is important to note that this does not include the cost of labor. If you are not comfortable doing the work yourself, you will need to factor in the cost of having a professional do the job.

In this blog post, we have discussed how to replace a carburetor on a Husqvarna weed eater. We have provided step-by-step instructions, as well as images and videos to help you along the way. We hope that this information has been helpful, and that you are now able to successfully replace the carburetor on your Husqvarna weed eater.

Here are some key takeaways from this blog post:

• Before you begin, make sure that you have the necessary tools and parts.
• Carefully follow the steps in the instructions, and be sure to take your time.
• If you are not comfortable working on your own lawn equipment, it is best to take it to a qualified technician.

We hope that this blog post has been helpful. If you have any questions, please feel free to leave a comment below.