How To Put String On Dewalt Weed Eater?

How to Put String on a DeWalt Weed Eater

Your DeWalt weed eater is a powerful tool that can help you keep your yard looking its best. But if the string breaks, you’ll need to know how to put a new one on. This is a simple process, but it’s important to do it correctly so that you don’t damage your weed eater.

In this article, we’ll walk you through the steps of putting string on a DeWalt weed eater. We’ll also provide some tips on how to choose the right string for your needs. So if you’re ready to get started, read on!

Step	Instructions	Image
1	Remove the old string from the weed eater.
2	Measure the length of string you need.
3	Thread the new string through the eyelets on the weed eater.
4	Tighten the string until it is taught.

This guide will show you how to put string on a Dewalt weed eater. This is a simple task that can be completed in a few minutes. By following these steps, you can ensure that your weed eater is properly maintained and that it will continue to function properly.

Gather Your Materials

• Dewalt Weed Eater
• Replacement string
• Pliers
• Tape measure

Remove the Old String

1. Turn off the weed eater and disconnect it from the power source.
2. Locate the string head. The string head is located on the front of the weed eater, just below the cutting blade.
3. Use the pliers to loosen the screws that hold the string head in place.
4. Remove the old string.

Install the New String

1. Cut a piece of replacement string that is about 18 inches long.
2. Thread the new string through the holes in the string head.
3. Pull the string taut and make sure that it is evenly distributed on both sides of the string head.
4. Tighten the screws that hold the string head in place.

Test the Weed Eater

Once you have installed the new string, turn on the weed eater and test it out. Make sure that the string is cutting through the weeds properly. If the string is not cutting through the weeds, you may need to adjust the tension of the string.

Replacing the string on a Dewalt weed eater is a simple task that can be completed in a few minutes. By following these steps, you can ensure that your weed eater is properly maintained and that it will continue to function properly.

Here are some additional tips for maintaining your Dewalt weed eater:

• Clean the weed eater after each use. This will help to prevent build-up of dirt and debris, which can damage the engine.
• Oil the weed eater regularly. This will help to keep the engine running smoothly.
• Replace the spark plug every year. This will help to ensure that the engine is getting the correct amount of spark.
• Inspect the weed eater for damage before each use. This will help to prevent accidents.

By following these tips, you can extend the life of your Dewalt weed eater and keep it running in top condition.

How to Put String on a Dewalt Weed Eater

Dewalt weed eaters are a popular choice for homeowners and professionals alike. They are powerful and efficient, and they can handle a variety of tasks. However, one of the most common problems with weed eaters is that the string can break. When this happens, it can be difficult to know how to put new string on the weed eater.

In this article, we will show you how to put string on a Dewalt weed eater. We will provide step-by-step instructions, and we will also discuss some common problems that you may encounter.

Step 1: Gather your tools

Before you begin, you will need to gather the following tools:

• A pair of pliers
• A screwdriver
• A new spool of weed eater string

Step 2: Remove the old string

The first step is to remove the old string from the weed eater. To do this, follow these steps:

1. Turn off the weed eater and disconnect it from the power source.
2. Locate the string head on the weed eater. The string head is usually located at the front of the weed eater, near the cutting blade.
3. Use the pliers to loosen the screws that hold the string head in place.
4. Remove the string head from the weed eater.
5. Use the pliers to remove the old string from the string head.

Step 3: Install the new string

Now that you have removed the old string, you can install the new string. To do this, follow these steps:

1. Cut a piece of new string that is the same length as the old string.
2. Thread the new string through the holes in the string head.
3. Tighten the screws to secure the string head in place.

Step 4: Test the weed eater

Once you have installed the new string, you should test the weed eater to make sure that it is working properly. To do this, follow these steps:

1. Turn on the weed eater and let it run for a few seconds.
2. Make sure that the string is spinning properly.
3. If the string is not spinning properly, adjust the tension until it is.

Weed eaters are a great tool for keeping your property free of weeds. By following these steps, you can easily put new string on your Dewalt weed eater and keep it running smoothly.

Here are some additional tips for maintaining your Dewalt weed eater:

• Clean the weed eater regularly to prevent build-up of dirt and debris.
• Sharpen the cutting blade regularly to ensure that it is cutting effectively.
• Replace the string head when it is worn out.

By following these tips, you can extend the life of your Dewalt weed eater and keep it running smoothly for years to come.

How do I put string on a Dewalt weed eater?

1. Turn off the weed eater and disconnect the spark plug wire. This will prevent the weed eater from starting accidentally while you are working on it.
2. Remove the old string. There are two ways to do this:

• If your weed eater has a bump head, hold the bump head down and pull the string out.
• If your weed eater has a spool, unscrew the spool and remove the string.

3. Thread the new string through the eyelets on the bump head or spool. Make sure the string is long enough to reach the ground when the weed eater is at full throttle.
4. Reattach the bump head or spool.
5. Reconnect the spark plug wire.
6. Test the weed eater to make sure it is working properly.

What type of string do I need for my Dewalt weed eater?

You will need to use a nylon trimmer line that is compatible with your weed eater. The size of the string will depend on the model of your weed eater.

How often do I need to replace the string on my Dewalt weed eater?

You will need to replace the string on your weed eater as soon as it starts to fray or break. This will help to ensure that your weed eater is operating at peak performance.

What is the best way to store my Dewalt weed eater?

The best way to store your Dewalt weed eater is to hang it up in a dry, well-ventilated area. This will help to prevent the weed eater from rusting or developing other problems.

What are some common problems with Dewalt weed eaters?

Some common problems with Dewalt weed eaters include:

• The weed eater won’t start. This could be caused by a number of problems, such as a dirty spark plug, a faulty fuel filter, or a bad carburetor.
• The weed eater is cutting unevenly. This could be caused by a dull blade or a bent shaft.
• The weed eater is smoking. This could be caused by a dirty air filter or a faulty carburetor.

How can I troubleshoot common problems with my Dewalt weed eater?

If you are having problems with your Dewalt weed eater, you can try to troubleshoot the problem yourself by following these steps:

1. Check the spark plug. If the spark plug is dirty, clean it with a wire brush. If the spark plug is damaged, replace it.
2. Check the fuel filter. If the fuel filter is clogged, replace it.
3. Check the carburetor. If the carburetor is dirty, clean it with carburetor cleaner. If the carburetor is damaged, have it repaired or replaced.
4. Check the air filter. If the air filter is dirty, clean it with a vacuum cleaner. If the air filter is damaged, replace it.
5. Check the blade. If the blade is dull, sharpen it or replace it.
6. Check the shaft. If the shaft is bent, have it repaired or replaced.

If you are unable to troubleshoot the problem yourself, you can take your weed eater to a qualified service center for repairs.