How To Start Stihl Weed Eater Fs 56 Rc?

How to Start a Stihl Weed Eater FS 56 RC

The Stihl FS 56 RC is a powerful and versatile weed eater that can handle a variety of tasks, from clearing brush to trimming hedges. But before you can get started using it, you need to know how to start it.

Starting a Stihl Weed Eater FS 56 RC is a simple process, but there are a few things you need to know to do it correctly. In this article, we’ll walk you through the steps of starting your Stihl Weed Eater FS 56 RC, so you can get up and running in no time.

We’ll cover everything from checking the oil level to pulling the starter rope, so you can be confident that you’re doing it right. So, if you’re ready to learn how to start your Stihl Weed Eater FS 56 RC, read on!

Step	Instructions	Image
1	Turn the choke to the “On” position.
2	Pull the starter rope slowly until you feel resistance, then pull quickly.
3	If the weed eater does not start, repeat steps 1 and 2.

How To Start Stihl Weed Eater Fs 56 Rc?

Preparing the Weed Eater

Before you can start your Stihl Weed Eater FS 56 RC, you need to make sure that it is properly prepared. This includes:

• Filling the fuel tank with the correct type of fuel.
• Checking the oil level and adding oil if necessary.
• Attaching the string trimmer head.
• Adjusting the string trimmer head height.

Filling the Fuel Tank

The Stihl Weed Eater FS 56 RC uses a mixture of gasoline and oil. The correct mixture is 50:1 gasoline to oil. You can purchase pre-mixed fuel from a hardware store or lawn and garden center, or you can mix your own fuel. If you are mixing your own fuel, use high-quality gasoline and oil. Do not use old or stale fuel, as this can damage the engine.

To fill the fuel tank, remove the fuel cap and carefully pour the fuel into the tank. Do not overfill the tank. The fuel level should be about 1 inch below the bottom of the filler neck. Replace the fuel cap and tighten it securely.

Checking the Oil Level

The Stihl Weed Eater FS 56 RC has an oil sight glass located on the side of the engine. To check the oil level, remove the oil dipstick and wipe it clean with a rag. Insert the dipstick back into the engine and remove it again. The oil level should be between the “full” and “add” marks on the dipstick. If the oil level is low, add oil to the engine until the level reaches the “full” mark.

Attaching the String Trimmer Head

The Stihl Weed Eater FS 56 RC uses a string trimmer head that is attached to the engine with a bolt. To attach the string trimmer head, first remove the bolt that secures the old head. Then, align the holes in the new head with the holes in the engine. Insert the bolt through the holes and tighten it securely.

Adjusting the String Trimmer Head Height

The Stihl Weed Eater FS 56 RC has a string trimmer head that can be adjusted to different heights. This allows you to trim grass at different heights. To adjust the string trimmer head height, loosen the knob on the side of the head. Then, move the head up or down until it is at the desired height. Tighten the knob to secure the head in place.

Starting the Weed Eater

Now that the weed eater is properly prepared, you can start it. To start the weed eater, follow these steps:

1. Turn the fuel valve to the “on” position.
2. Pull the starter rope slowly until you feel resistance. Then, pull the rope quickly and firmly. The engine should start.
3. Allow the engine to warm up for a few seconds before using it.

Using the Weed Eater

Once the weed eater is started, you can use it to trim grass and weeds. To do this, hold the weed eater with both hands and grip the handle firmly. The throttle control is located on the handle. To increase the speed of the engine, slide the throttle control forward. To decrease the speed of the engine, slide the throttle control back.

To trim grass, hold the weed eater so that the string trimmer head is about 1 inch above the ground. Then, move the weed eater back and forth in a sweeping motion. Be careful not to touch the string trimmer head to the ground, as this could damage the head.

To trim weeds, hold the weed eater so that the string trimmer head is about 2 inches above the ground. Then, move the weed eater back and forth in a sweeping motion. Be careful not to touch the string trimmer head to the ground, as this could damage the head.

Stopping the Weed Eater

To stop the weed eater, release the throttle control and pull the starter rope slowly until the engine stops. Then, turn the fuel valve to the “off” position.

Troubleshooting

If the weed eater is not starting, there are a few things you can check:

• Make sure that the fuel tank is full and that the fuel valve is turned to the “on” position.
• Make sure that the oil level is correct.
• Check the spark plug and make sure that it is clean and properly gapped.
• Check the air filter and make sure that it is clean.

If you have checked all of these things and the weed eater is still not starting, you may need to take it to a qualified repair shop.

Operating the Weed Eater

Once the weed eater is started

How To Start Stihl Weed Eater Fs 56 Rc?

The Stihl FS 56 RC is a powerful and versatile weed eater that can be used for a variety of tasks, from trimming around the edges of your lawn to clearing brush. However, like any other piece of machinery, it can be difficult to start if you don’t know what you’re doing.

In this guide, we’ll walk you through the steps on how to start your Stihl FS 56 RC weed eater. We’ll cover everything from checking the oil level to priming the engine. So, whether you’re a first-time user or you’re just looking for a refresher, read on for all the information you need to know.

1. Checking the oil level

Before you start your Stihl FS 56 RC weed eater, it’s important to check the oil level. To do this, follow these steps:

1. Locate the oil fill cap on the side of the engine.
2. Remove the cap and use the dipstick to check the oil level.
3. The oil level should be between the “full” and “add” marks on the dipstick.
4. If the oil level is low, add oil until it reaches the “full” mark.

2. Priming the engine

Once you’ve checked the oil level, you’ll need to prime the engine. To do this, follow these steps:

1. Locate the primer bulb on the side of the engine.
2. Squeeze the primer bulb five times.
3. Let go of the primer bulb and wait a few seconds.

3. Starting the engine

Now that you’ve checked the oil level and primed the engine, you’re ready to start it. To do this, follow these steps:

1. Turn the choke to the “on” position.
2. Pull the starter rope slowly until you feel resistance.
3. Continue pulling the starter rope until the engine starts.
4. Once the engine starts, release the choke and let it run for a few seconds.

Troubleshooting

If your Stihl FS 56 RC weed eater won’t start, there are a few things you can check:

• Make sure that the oil level is correct.
• Make sure that the primer bulb is primed.
• Check the spark plug for damage.
• Clean the carburetor.

If you’re still having trouble starting your weed eater, you can take it to a qualified Stihl dealer for service.

Starting your Stihl FS 56 RC weed eater is a simple process, but it’s important to follow the steps carefully to avoid damage to the engine. By following the steps in this guide, you’ll be able to start your weed eater in no time.

Here are some additional tips for using your Stihl FS 56 RC weed eater:

• Wear safety glasses and gloves when operating the weed eater.
• Keep the weed eater’s cutting head sharp.
• Inspect the weed eater regularly for damage.
• Store the weed eater in a safe place when not in use.

By following these tips, you can safely and effectively use your Stihl FS 56 RC weed eater for many years to come.

How do I start my Stihl Weed Eater FS 56 RC?

1. Make sure the trimmer is turned off and the spark plug wire is disconnected.
2. Check the fuel level. The fuel tank should be at least half full.
3. Prime the engine. To do this, press the primer bulb several times until fuel flows into the carburetor.
4. Attach the spark plug wire. Make sure the wire is securely connected to the spark plug.
5. Turn the trimmer on. Press the start button and hold it until the engine starts.
6. Adjust the throttle. Turn the throttle control to the desired speed.

What if my trimmer won’t start?

There are a few possible reasons why your trimmer won’t start. Here are some troubleshooting tips:

• Check the spark plug. Make sure the spark plug is clean and properly gapped.
• Check the fuel filter. The fuel filter may be clogged, preventing fuel from reaching the carburetor.
• Check the carburetor. The carburetor may be dirty or out of adjustment.
• Check the air filter. The air filter may be clogged, preventing air from reaching the carburetor.

If you have checked all of these things and your trimmer still won’t start, you may need to take it to a qualified repair shop.

How do I change the spark plug on my Stihl Weed Eater FS 56 RC?

1. Turn off the trimmer and allow it to cool down.
2. Remove the spark plug boot. Use a spark plug wrench to loosen the spark plug boot and remove it from the spark plug.
3. Unscrew the spark plug. Use a spark plug wrench to unscrew the spark plug from the engine.
4. Install the new spark plug. Make sure the new spark plug is the correct size and type for your trimmer. Hand-tighten the spark plug until it is snug, then use the spark plug wrench to tighten it another 1/8 to 1/4 turn.
5. Reattach the spark plug boot. Make sure the spark plug boot is securely attached to the spark plug.

How do I change the fuel filter on my Stihl Weed Eater FS 56 RC?

1. Turn off the trimmer and allow it to cool down.
2. Locate the fuel filter. The fuel filter is usually located on the bottom of the trimmer, near the carburetor.
3. Remove the fuel filter cover. Use a screwdriver to remove the fuel filter cover.
4. Remove the old fuel filter. Use a pair of pliers to grasp the old fuel filter and pull it out of the housing.
5. Install the new fuel filter. Make sure the new fuel filter is the correct size for your trimmer. Insert the new fuel filter into the housing and tighten it until it is snug.
6. Replace the fuel filter cover. Use a screwdriver to replace the fuel filter cover.

How do I clean the carburetor on my Stihl Weed Eater FS 56 RC?

1. Turn off the trimmer and allow it to cool down.
2. Remove the air filter. Use a screwdriver to remove the air filter cover. Then, remove the air filter from the trimmer.
3. Locate the carburetor. The carburetor is usually located on the top of the trimmer, near the engine.
4. Remove the carburetor cover. Use a screwdriver to remove the carburetor cover.
5. Clean the carburetor. Use a carburetor cleaner to clean the inside of the carburetor. Be careful not to damage the carburetor jets.
6. Reassemble the carburetor. Reinstall the carburetor cover, air filter, and air filter cover.

How do I adjust the throttle on my Stihl Weed Eater FS 56 RC?

The throttle on a Stihl Weed Eater FS 56 RC is used to control the speed of the engine. To adjust the throttle, follow these steps:

1. Locate the throttle control. The throttle control is usually located on the handle of the trimmer.
2. Turn the throttle control to the desired speed. The throttle control has a number of settings, from low to high. Turn the control to the desired speed.

Note: Be careful not to turn the throttle control too high, as this could damage the engine.

In this blog post, we have discussed how to start a Stihl Weed Eater FS 56 RC. We have covered the following topics:

• How to check the oil level
• How to add oil to the Weed Eater
• How to attach the string trimmer head
• How to start the Weed Eater
• How to adjust the speed of the Weed Eater
• How to stop the Weed Eater

We hope that this blog post has been helpful. If you have any other questions about how to use your Stihl Weed Eater, please consult the owner’s manual.